ANTAIRA EVC-3001 Manuale Utente

ANTAIRA TECHNOLOGIESEthernet Extender over VDSL2Media ConverterEVC-3001 & EVC-3010User’s Manual

101.3 Key FeaturesThe Ethernet over VDSL2 Converter provides the following key features:Cost-effective VDSL2 CO / CPE bridge solution lOne bo

111.4SpecicationsProduct EVC-3001 EVC-3010Hardware SpecicationPorts10/100Tx1 x RJ-45,Auto-negotiation Auto-MDI/MDI-X1 x RJ-45,Auto-negotiation Auto

12Performance* (Down Stream /Up Stream)Asymmetric Mode200m -> 100/55Mbps400m -> 90/50Mbps600m -> 70/40Mbps800m -> 60/25Mbps1000m -> 45/

13Storage Temperature -10~70 Degree COperating Humidity 10% to 90%, relative humidity, non-condensingStorage Humidity 10% to 90%, relative humidity,

142. Hardware DescriptionEVC-3001 lThe EVC-3001 provides 2 RJ-11 ports for voice connection (like telephone) and for network line connection.

15EVC-3010 Front Panel nFigure 2-2: EVC-3010 Front Panel2.1.1 LED Indicators for EVC-3001 and EVC-3010The rich diagnostic LEDs on the front p

1610/100Tx Port nLED Color FunctionLNK/ACT GreenLight Indicate that the port is Link Up.Fast BlinkIndicate that the Converter is actively sending or r

17summary table of transmission setting; bandwidth and distance extensibility tested for AWG 24 (0.5mm) twisted-pair without noise and c

18metric by their own. When Symmetric is selected that provides better upstream performance, when Asymmetric is selected that provides

193. Installation3.1 Install Ethernet over VDSL2 ConverterThe Ethernet over VDSL2 Converter does not require any software conguration. User

TrademarksCopyright © Antaira Technologies 2013.Contents subject to revision without prior notice.Antaira is a registered trademark of Antaira

203.1 EVC-3001 / EVC-3010 LAN to LAN ConnectionTwo sets of the Ethernet over VDSL2 Converters could be used to link two local Area netw

213.2 Connecting EVC-3001 / EVC-30103.2.1 Connecting Standalone PCRefer to the following procedures to setup the EVC-3001 to a standalone P

223.2.2 Connecting Multiple PCs to an Ethernet LANRefer to the following procedures to setup the EVC-3001 to an Ethernet LAN.1. Set the EVC

233.3 Connecting EVC-30103.3.1 Connecting Standalone IP DeviceRefer to the following procedures to setup the EVC-3010 to a standalone PC.1.

243.3.2 Connecting Multiple PCs to an Ethernet LANRefer to the following procedures to setup the EVC-3010 to an Ethernet LAN.1. Set the EVC

254. Power InformationThe power jack of EVC-3001 / EVC-3010 is with 2.5mm in the central post and required +5VDC power input. It will confo

265. Troubleshooting SYMPTOM:VDSL LNK LED does not light after wire is connected to the VDSL port.CHECKPOINT:1. Verify the length of th

276. FAQQ1: What voltage that EVC-3001 / EVC-3010 used?A1: 5V DC, 2AQ2: What is VDSL2?A2: VDSL2 (Very High-Bit-Rate Digital Subscriber Line

28the ratio, the easier it is to identify and subse quently isolate and eliminate the source of noise. Generally speaking, the higher SNR valu

FCC WarningThis equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part

WEEE WarningTo avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and

Table of Contents1. Introduction ... 6 1.1 Checklist ...

61. Introduction1.1 ChecklistCheck the contents of the package for following parts:EVC-3001 x 1; or EVC-3010 x 1 l5V DC/ 2A AC-to-DC Power Adapter x

725/4Mbps for asymmetric data rate at 1.6km. The performance of EVC-3010 (BNC) is up to 100/65Mbps for asymmetric data rate within 2

8Telephone wire100Base-TX UTPVDSL2 Coaxial CableVDSL2Main office/PBX, Telco CO, wire closetExisting Telephone NetworkIP CameraIP CameraEthernet Switch

9Telephone wire100Base-TX UTPVDSL2 Coaxial CableVDSL2Main office/PBX, Telco CO, wire closetExisting Telephone NetworkEthernet over VDSL and Telephone